ZDF
Sign inSign up

Vulnerabilities

Vulnerability · CVE-2026-10674

The NXP LPUART serial driver (drivers/serial/uart_mcux_lpuart.c), when CONFIG_UART_USE_RUNTIME_CONFIGURE is enabled, called LPUART_Deinit() at the start of mcux_lpuart…

Published Jul 21, 2026 · catalog updated Oct 15, 2026 · the affected product

Check if you run it

No confirmed exploitation is on record for CVE-2026-10674. EPSS is 0.14%. Act only if a listed version of the affected product is installed.

Gaps on this record

  • No plain product name is stored. The page cannot tell you which product to check.
  • No version range is stored. A customer cannot check an installed version against this record.
  • No vendor fix or required action is stored. Compare the linked advisory before you change production.
Severity
Medium5.5
Known exploitation
Not in CISA/VulnCheck KEV
EPSS
0.14%
Remediation
Advisory link
Affected products
cpe zephyrproject/zephyr

The NXP LPUART serial driver (drivers/serial/uart_mcux_lpuart.c), when CONFIG_UART_USE_RUNTIME_CONFIGURE is enabled, called LPUART_Deinit() at the start of mcux_lpuart_configure(), which disables the LPUART peripheral clocks. The requested configuration is validated only afterwards (in mcux_lpuart_configure_basic), and unsupported parity/data-bit/stop-bit/flow-control values return -ENOTSUP before the clock is re-enabled. As a result, a uart_configure() request with an unsupported configuration left the LPUART in a clock-disabled state; any subsequent access to LPUART registers (poll_out/poll_in, interrupt handling, or a later reconfigure) faults on the gated peripheral and escalates to a hard fault, crashing the system. uart_configure() is a Zephyr syscall whose verifier (z_vrfy_uart_configure) only checks that cfg is readable user memory and forwards the caller-supplied configuration unchanged, so an unprivileged userspace thread with access to an LPUART device can deterministically trigger the fault, a persistent system-wide denial of service. Introduced in v2.5.0 and present in all subsequent releases until this fix, which removes the LPUART_Deinit() call and instead only disables the transmitter/receiver, leaving the clock running.

Are you affected?

Enter the version you run. The result uses only the ranges stored on this record.

The check returns affected, not affected, or incomplete. It does not guess a version that is missing from the record.

  • cpe zephyrproject/zephyrversion unspecified

How to fix CVE-2026-10674

What to do

Three questions, each answered from this record only. Confirm the vendor advisory before you patch.

Should you patch?

No confirmed exploitation is on record for CVE-2026-10674. EPSS is 0.14%. Act only if a listed version of the affected product is installed.

Which versions are affected?

Affected version ranges are not on this record. Compare the installed version with the linked vendor advisory before you change production.

What should an analyst verify?

CWE-617. EPSS 0.14%. There is no CISA KEV listing. No Exploit-DB or Metasploit reference is linked. Use the source links for the original advisory.

Code

The project this record applies to. Exploit listings stay in References.

Timeline

Detection, updates, and resolution for this record.

  1. Jul 21, 2026 · NIST NVD

    Detected

    The NXP LPUART serial driver (drivers/serial/uart_mcux_lpuart.c), when CONFIG_UART_USE_RUNTIME_CONFIGURE is enabled, called LPUART_Deinit() at the start of mcux_lpuart_configure(), which disables the LPUART peripheral clocks. The requested configuration is validated only afterwards (in mcux_lpuart_configure_basic), and unsupported parity/data-bit/stop-bit/flow-control values return -ENOTSUP before

  2. Oct 15, 2026 · NIST NVD

    Updated

    The NXP LPUART serial driver (drivers/serial/uart_mcux_lpuart.c), when CONFIG_UART_USE_RUNTIME_CONFIGURE is enabled, called LPUART_Deinit() at the start of mcux_lpuart_configure(), which disables the LPUART peripheral clocks. The requested configuration is validated only afterwards (in mcux_lpuart_configure_basic), and unsupported parity/data-bit/stop-bit/flow-control values return -ENOTSUP before

Sources

  • CVE.orgVulnerability recordCVE-2026-10674

    Official CVE identifier

    cve.org
  • FIRST EPSSExploitation probabilityCVE-2026-10674

    30-day exploitation probability 0.1%

    first.org
  • NIST NVDVulnerability recordCVE-2026-10674

    The NXP LPUART serial driver (drivers/serial/uart_mcux_lpuart.c), when CONFIG_UART_USE_RUNTIME_CONFIGURE is enabled, called LPUART_Deinit() at the start of mcux_lpuart_configure(), which disables the LPUART peripheral clocks. The requested configuration is validated only afterwar

    nvd.nist.gov

References

Freshness

Last verified in this catalog Oct 18, 2026. Significant claims (KEV, EPSS, CVSS, affected ranges) come from the source rows above — open the original publisher for the authoritative advisory.